How to read BMW Freescale MC9S12D64 with Xprog V5.60

Here's the DIY guide for those whom want to get tripple blinker on their BMW E46.

DIY:
1) you need LSZ module with =>SW3.6 on sticker
2) xprog v5.55 v5.60 or above with mc9s12 bdm adapter
3) sticked dump of ci37 (eeprom virgined, need to be coded after installing ecu to car)

wires color legend (follow xprog box connection manual for mc9s12d64):
blue - reset
red - VCC
green - BKGD
yellow - xclks
white - extal
gray - GND

ground wire instead of soldering to pcb can be ezly connected to pin 32 in connection socket.

(Click to enlarge)


Result here:

Free download: lsz_c37_xprog.zip


Credit to MeMpHiSj from MHHAUTO

http://www.obdii365.com/producttags/xprog.html

Benz Sprinter 2010 EZS Soldering Pinouts to Xprog

Purpose: 

Do odometer correction on 2010 Sprinter Van. I need the soldering points for the ezs/eis.I can't actually see the mask but after extensive reading every points to them having the 0L01Y mask. Which programmer will work?



Solution:

R260 original ok
clone rosfar,ok
xprog clone ok
R270 ok


Use xprog the pinouts for xprog is what posted below. i always do this with xprog and never had a problem just select in device options " read and verify " make sure it is NOT selected and you should be ok , use the BDM adaptor with xprog for it
here is the settings i use and you know the story always keep backup of the files you read











BTW:


Here are R270 wires:

2- +5v

24,26- ground

7- reset

19- background

BMW F series Airbag MAC7241 Pinout to Xprog

How to use Xprog m box ecu programmer to read BMW F series Airbag?

Check pinouts below:

http://www.obdii365.com/producttags/xprog.html

Read Volvo S40/V50/C30/C70 MCU MC9S12DG256

Read Volvo S40/V50/C30/C70 2004 MCU MC9S12DG256 80 QFP  by xprog m box ecu programmer. 

Picture and pinout attached:

Click to enlarge all images. 


http://www.obdii365.com/wholesale/v570-xprog-m-ecu-programmer.html

Xprog can unlock KVM secured & read MCU 9S12XEQ384

Test report: Xprog box running the latest software version 5.8 is able to Read MCU 9S12 XEQ 384 from a Range Rover 2015-2016.

Save P-FLASH and D-FLASH unlock KVM secured.

Now, i’ll show you the location of a KVM module

And remove the module with secured MCU9S12XEQ

Read on bench with Xprog HQ clone or original

Then will save P-FLASH and D-FLASH unlock KVM secured

Here you go.

The module location inside Range Rover 2015-2016

The Xprog m ecu programmer

The KVM board

Secured MCU 9S12 XEQ

Pin 42 and 46

Lift 1 pins shown in the photo

Maximum wires length 12cm

Secured MCU 9S12 XEQ 384

Run Xprog software v5.8

MCU/MPU, Freescale NXP 9S12XE, MC9S12XEQ384 D-FLASH-Secured

Tip & Guide: How to get Xprog to work with secured MCU:

Reset MCU security

Run->change security state->reset MCU security

Wait 10…15 seconds if not success, cancel process

Check connection

Start from a

Remember MCU security byte value

Read, write…commands can be executed many times

Set MCU security

Run->change security sate->set MCU security

Read

Reset MCU security

It will take 10 to 12 seconds to unlock MCU

IP NOT STOP and repeat

Read

Save data

MCU/MPU, Freescale NXP 9S12XE, MC9S12XEQ384 P-FLASH-Secured

Read

Save data

Job’s done!

Now you can upload the data and generate new key file with key programmers, i.e VVDI2 v5.6.0 above or Mart Tool. Then write data back to KVM.

Related Post:

Mart Tool Program Range Rover 2015 FK72 KVM All Keys Lost

http://blog.obdii365.com/2018/07/04/xprog-v5-8-reads-mcu-9s12xeq384-from-rang-rover-2015/