Manufacturer of AEC302C / AEC400 CDI controllers didn’t left possibility to
access internal MCU memory by K-Line. Therefore it is really possible to reset
them if you have any MOTOROLA MC68HC05E6 programmer (XPROG / XPROGm,
UPA, CARPROG, ELNEC, etc.).
Opening the plastic casing
Make a cut around plastic casing to gain access to the printed circuit board (PCB).
Don’t cut too deep – you can damage electrolytic capacitors near the edges of
plastic casing!
Clean the PCB from epoxy sealant. It is significantly easier to clean if sealant is
heated using hot air station or other source of hot air (fan, etc.) – it becomes
crumbly and comes out without excessive effort.
How to connect MCU programmer
NOTE. Wire colors in the picture, corresponds to CARPROG cable A10. Signal
symbols B2, B3, B5, B6, Vcc, Vpp – to XPROG / XPROG-m programmer.
Change data at marked position from 00 to 01. This way you will change CDI
controller state to NEVER PROGRAMMED. CDI controller is ready now to store
new code on the first time ignition is switched to ON with a master key.
NOTE. Ignition must be switched on with valid MASTER key that belongs to
immobilizer controller IMM003 / IMM006.
no programmer can do everything but if you have vvdiprog, xprog Clone and upa ori you can do 99 percent of all and you pay only 650 bucks for all of them. In my country thats a good Deal
no programmer can do everything but if you have vvdiprog, xprog Clone and upa ori you can do 99 percent of all and you pay only 650 bucks for all of them. In my country thats a good Deal
Info for read audi a6 ELV (Steering lock)1L59W/3L40K with Xprog 5.55 (clone) tested by 6 PCB and successfully done without any problems
Read/Write eeprom.successfully
Read/Write flash.successfully
MCU SECURED!
Xhorse VVDI Prog the best for this job!
A lot of time read ELV from AUDI with vvdi prog.
But xprog is mucj cheaper than vvdi prog.
1.Disable anti-virus program when downloading software and running software.
2.Uninstall all the software and USB drivers of the old version xprog-box on your computer, then install the new XPROG5.84 software.
3. Run 5.84Regsisty program for several times when installing software
4.Run 5.84Regsisty file for 2 times before you run software everytime .
XPROG-M V5.84 Authorizations: AUTH-0001 Motorola HC05 family authorization (allows to read/write EEPROM) AUTH-0002 Motorola HC08 family authorization (allows to read/write EEPROM) AUTH-0003 Motorola HC11 family authorization (allows to read/write EEPROM) AUTH-0004 Motorola HC12, 9S12 family authorization (allows to read/write EEPROM and flash memory) AUTH-0005 Texas Instruments TMS370/TMS374 family authorization (allows to read/write EEPROM) AUTH-0006 Motorola HC05Bxx and HC05Xxx family bypass security authorization (allows to read/write secured EEPROM and flash memory) AUTH-0007 ST M35080 authorization. Read/Write/Erase device to delivery state. AUTH-0008 BMW EWS3 authorization AUTH-0009 ATMEGA family authorization (allows to read/write EEPROM and flash memory) AUTH-0010 MB ZGS001 authorization AUTH-0011 Motorola HC11EA9/E9 bypass security authorization (allows to bypass security bit and read EEPROM and RAM memory) AUTH-0012 National CR16 authorization (allows to read/write EEPROM memory) AUTH-0014 ST7, ST10 family authorization (allows to read/write internal flash) AUTH-0015 MPC5xx authorization (depending on device program automatically detects MPC5xx, M95xxx device type, flash, external flash and configuration memory size) AUTH-0018 Motorola HC12, HC912, MC9S12, MC9S12X bypass security authorization (allows to read/write secured EEPROM and flash memory) AUTH-0020 ARM (Micronas, …) Family authorization (allows to read/write internal flash and external serial EEPROM) AUTH-0021 ARM (Micronas, …) Family bypass security authorization (allows to read/write secured and non-secured internal flash and external serial EEPROM, view/change mileage, Chassis number (VIN), serial number and PIN code). AUTH-0023-1 MAC7xxx AUTH-0023-2 XC23xx AUTH-0024-1 MC9S12Cxx AUTH-0024-2 MC9S12XE AUTH-0024-3 9S12XE SECURITY AUTH-0024-4 MC9S12HA/HY/P AUTH-0025-1 MPC/SPC5xxx Authorized 2016/3/13
Add new authorization: AUTH-0028-1 Renesas V850 Authorized and AUTH-0028-2 Renesas SuperH Authorized 2017/10/9Language: English
XPROG-M V5.84 Authorizations: AUTH-0001 Motorola HC05 family authorization (allows to read/write EEPROM) AUTH-0002 Motorola HC08 family authorization (allows to read/write EEPROM) AUTH-0003 Motorola HC11 family authorization (allows to read/write EEPROM) AUTH-0004 Motorola HC12, 9S12 family authorization (allows to read/write EEPROM and flash memory) AUTH-0005 Texas Instruments TMS370/TMS374 family authorization (allows to read/write EEPROM) AUTH-0006 Motorola HC05Bxx and HC05Xxx family bypass security authorization (allows to read/write secured EEPROM and flash memory) AUTH-0007 ST M35080 authorization. Read/Write/Erase device to delivery state. AUTH-0008 BMW EWS3 authorization AUTH-0009 ATMEGA family authorization (allows to read/write EEPROM and flash memory) AUTH-0010 MB ZGS001 authorization AUTH-0011 Motorola HC11EA9/E9 bypass security authorization (allows to bypass security bit and read EEPROM and RAM memory) AUTH-0012 National CR16 authorization (allows to read/write EEPROM memory) AUTH-0014 ST7, ST10 family authorization (allows to read/write internal flash) AUTH-0015 MPC5xx authorization (depending on device program automatically detects MPC5xx, M95xxx device type, flash, external flash and configuration memory size) AUTH-0018 Motorola HC12, HC912, MC9S12, MC9S12X bypass security authorization (allows to read/write secured EEPROM and flash memory) AUTH-0020 ARM (Micronas, …) Family authorization (allows to read/write internal flash and external serial EEPROM) AUTH-0021 ARM (Micronas, …) Family bypass security authorization (allows to read/write secured and non-secured internal flash and external serial EEPROM, view/change mileage, Chassis number (VIN), serial number and PIN code). AUTH-0023-1 MAC7xxx AUTH-0023-2 XC23xx AUTH-0024-1 MC9S12Cxx AUTH-0024-2 MC9S12XE AUTH-0024-3 9S12XE SECURITY AUTH-0024-4 MC9S12HA/HY/P AUTH-0025-1 MPC/SPC5xxx Authorized 2016/3/13
1. Windows XP 32bit OR windows 7 64 bit, all the patch software for the windows system should be installed already and the windows properly works well…
2. The windows system should be with at lest 2 partitions (except the CD ROM.)
3. Can not be working with virtual hard disk.
How to install xprog V5.84 on Windows 7?
Installation steps:
1. Click the file “installation.reg”, get the file information to the regedit.
2. Install the file “AdbeRdr11000_zh_CN.exe”, it is a must, otherwise the Xprog software will not start.
3. Plug the Xprog main interface to the computer, install the USB driver.
4. Copy the folder “XPROG-BOX5.84” to the desktop, and open it, and run the “xprogdesktop.exe”, then software open.
Q: Could I use xprog-m to read EWS3 mask 2D47J mcu? Does it work fine?
A: Yes you can,works fine.
ews3 2D47J can read/write in circuit with xprog.
but you need lift pin TXD 2D47J
You will erase eeprom everytime. If you want to read 2D47J through Kline then you must first remove the MCU from circuit board and then read in adaptor 2 times first, this will bypass the chips security, you can then solder back to board and read through KLine.
If it is with K-line, desolder it ,and read with ETL - is the best and safer way
through k-line is lottery.
